Autojack
Gardenjack
Lumberjack
Starrett
Trend
Bandsaws
Chainsaws
Circular Saws
Drilling & Nailing
Grinders
Heat Guns
Jigsaws
Lathes
Mitre Saws
Mixers
Multi Tools
Planers & Thicknessers
Plunge Saws
Pressure Washers
Reciprocating Saws
Routers
Sanders
Scroll Saws
Spray Guns
Table Saws
Tile Cutters
Workshop & Extraction
Compressors & Air Tools
Engine Tools
Garage & Workshop
Generators & Welders
Heaters
Sockets & Spanners
Trolley Jacks
Chisels
Circular Cutting Jigs
Clamps
Dovetail Jigs
Drill Bits
Hand Saw
Hex Key Sets
Jigs
Measuring
Paint Rollers
Pocket Hole Jig
Screwdriver Sets
Staplers
Water Pump
Bandsaw Blades
Circular Saw Blades
Jigsaw Blades
Multi Tool Blades
Planer Blades
Reciprocating Saw Blades
Scroll Saw Blades
Batteries
Chargers
Impact Wrench
Kits
Sanding
Torches
Adaptor Sets
Air Filters
Air Kits
Backing Pads
Brackets
Car Sponges
Catalogues
Collets
Extension Beds
Face Mask
Filter Bags
Gift Vouchers
Guide Bush
Guide Rails
Hats
Hoses
Key Cabinet
Lathe Chucks
Mitre Shears
Nails & Staples
Roller Heads
Rotary Accessory Sets
Rotary Brush
Router Cutters
Sanding Pads
Spanner Racks
Stands & Work Benches
Storage Bags
Swivel Castors
T Square
Table Extensions
Trolley Jack Accessories
Welding Helmets
Worktop Jig
Automotive
Cordless
Hand Tools
Package Deals
Power Tools
Spares & Accessories
The bigger brother of the BS305, this floorstanding woodworking bandsaw has a cutting capacity of 230mm (9"), to satisfy professional workshops. The power is delivered by a quiet induction motor with a belt drive to the bandsaw wheel. A two speed pulley allows the correct blade speed to be selected, depending on the hardness of the material being cut. The key to straight and accurate cutting on a bandsaw is to have a good set of blade guides. The Lumberjack BS340 has three bearings on the blade guard. Two sealed bearings mounted side-on to the blade, control blade twist and keep it true. The rear bearing takes the thrust of the back of the blade allowing it to run freely. The same setup is then repeated beneath the table.
Lumberjack Circle Cutting Jig Accessory For Bandsaws BS340
Quantity
Starrett Bandsaw Blade 2560mm x 13mm x 6TPI for BS340
Starrett Bandsaw Blade 2560mm x 10mm x 4TPI for BS340
The cast iron table tilts from 90 degrees to 45 degrees, on a rack & pinion, and has a positive stop at both of those positions. Any angle in between can be read off the scale and locked in. For rip cuts the guide fence can be situated on either side of the blade, can be locked into position with a single press of the lever and has a clear marker to set against the metric scale. The fence itself can be fitted in two ways. When cutting thicker material the full face height of 60mm is used. When cutting thin and narrow strips the fence is fitted with the small face, against the blade to allow clearance around the guides. The bandsaw is fitted with an LED work light on a flexible stem, so that the work area will always be well lit.
The two doors are fitted with safety locks which cut power to the motor when the doors are open for blade changing or cleaning.
Tensioning the blade correctly is made simple thanks to the features on this premium model. A blade tension lever quickly sets the tension. After a blade change fine tuning can be carried out with the aid of a tension indicator and scale. The required tension varies according to blade width. A window in the top door allows the operator to confirm blade tension is correct and make an adjustment when necessary.
A dust extractor is always recommended when using a bandsaw. The dust collection outlet has 3 rings which allow it to accept 3 sizes of hose, 50mm, 75mm & 100mm diameter making it compatible with any type of extraction system. If extraction is not being used however, the bandsaw is fitted with an integral dust collection draw. Dust falling into the base of the machine will be collected here, allowing it to be quickly and easily emptied.
Supplied with rip fence, mitre fence, work light, floorstand, cable and plug.
Lumberjack BSC340 Circle Cutting Jig Accessory For Bandsaw
The New Lumberjack BSC340 circle cutting jig has been brought out after we received a huge number of requests for one. These Jig's allow you to accurately and easily cut varying sized circles with your bandsaw. These are perfect for bowl and plate templates, Decorative work or any other application a perfect circle is required. As well as cutting perfect circles this jig can be used to cut uniform rounded edges, or more precise circular shaped designs.
"View Detail" will open a new browser tab.
Starrett WoodPecker Premium carbon blades have a hardened spring tempered back and ground, positive angle precision set teeth.
